Cruiser Uno 2.5Litri

Cruiser Uno 2.5Litri
Pret: 143 Euro
pret cu TVA
Cruiser Uno 2.5Litri
Vopsea antivegetativa pentru barci cu motor( viteza pana la 25noduri) si veliere/yachturi. Asigura protectie un singur sezon. Nu se foloseste pentru corputi de barca din aluminiu, sau metal zincat. Acoperire: 8.5mp/litru aplicare cu pensula.

One coat antifouling designed for both power (up to 25 knots) and sailing boats. Single season's antifouling protection. In most cases there is no need to seal main stream antifouling schemes and no need to sand before re-coating. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Coverage: 8.50 sq.m./ltr brushed and 3.0 sq.m./ltr sprayed.

 Colour SHELL WHITE

Designed for both motor boats (up to 25 knots) and sailing boats.Contains Copper Oxide and Preventol A4S
 
Application Details - Cruiser UNO
 Area  Below the waterline
 Finish/Sheen  Matt
 Thinner:  YTA085
 Number of Coats:  1-2 coats as specified
 Method of application:  Brush / Roller / Airless Spray / Airmix
 Available Shades:  View colour chart and sales codes 
 Pack sizes:  3LT
 Suitable for high speed craft?  NO

 

PRODUCT DESCRIPTION
One coat antifouling designed for both power (up to 25 knots) and sailing boats.
* Single season's antifouling protection
* In most cases there is no need to seal main stream antifouling schemes
* No need to sand before re-coating
 
PRODUCT INFORMATION
Colour YBA203-Shell White
Finish Matt
Specific Gravity 1.6
Volume Solids 49% average
Typical Shelf Life 2 yrs
VOC (As Supplied) 440 g/lt
Unit Size 2.5 litri
 
DRYING/OVERCOATING INFORMATION
 
Drying
  5ºC 15ºC 23ºC 35ºC
 
Touch Dry [ISO] 1hrs 45mins 30mins 20mins
Immersion 7hrs 5hrs 2hrs 2hrs
 
Overcoating
Substrate Temperature
  5ºC 15ºC 23ºC 35ºC
Overcoated By Min Max Min Max Min Max Min Max
 
Cruiser UNO  16hrs  ext  10hrs  ext  6hrs  ext  4hrs  ext
 
Preparation PREVIOUSLY ANTIFOULED SURFACE:
In Good Condition: Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON: Interprotect or Primocon.
LEAD: Etch Primer followed by Interprotect or Primocon.
WOOD: Preserve, if required, with Intertox. Prime with Interprotect or Primocon.
   
Method Apply 1 coat only. 2 coats will be required in the first season if applying to a new hull, one that has been stripped back to bare substrate, or over antifouling in poor condition. 2 coats are recommended for leading and trailing edges, waterline, rudder and keel.
   
Hints Mixing Stir well before use.
Thinner YTA085 Thinners No.3
Thinning Thinning is not recommended.
Cleaner YTA085 Thinners No.3
Ventilation and Humidity Control Ensure adequate ventilation during use.
Airless Spray Pressure: 176-210 bar. Tip Size: 2180.
Other For Airmix spray application: Pressure: 2.5 bar. Tip Size: 20-113. True colour will develop after immersion. Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness.
   
Some Important Points To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum -5ºC and maximum 35ºC. Ambient temperature should be minimum -5ºC and maximum 35ºC. Substrate temperature should be minimum 1ºC above dew point and maximum 35ºC.
   
Compatibility/Substrates GRP, Wood, Steel/Iron, Lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Can be applied direct over most types of antifoulings, provided they are in sound condition. Not compatible with VC 17m systems. Please contact your local International Coatings Ltd. representative for further information.
   
Number of Coats 1-2 coats as specified
   
Coverage (Practical) - 8.50 (m²/lt) by brush; 3.0 m²/lt spray.
   
Recommended DFT 52 microns dry by brush
Recommended WFT 106 microns wet by brush
   
Application Methods Brush, Roller, Airless Spray, Airmix

Available Sales Codes/Colours

YBA203
Shell White
YBA210
Blue
YBA234
Navy
YBA255
Red
YBA295
Black

Pretul se poate schimba fara notificare prealabila. Poza este doar orientativa, e posibil ca in poza sa existe accesorii neincluse in pachet.